Russound Collage Installation Manual Page 10
- Page / 28
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
10 Russound Collage System Installation Manual
Overview
As the home's electrical network is being used to transmit HomePlug
Power Line Carrier (PLC) signals, it is important to have the most robust
communication network possible. This is why intended installation
locations are pre-qualied BEFORE committing to a location and making
a hole in the wall.
Preparation
To perform binding and network verication you will need:
CAK1 keypad with pigtail (have all planned keypads on hand)•
CMM1 Media Manager and power cord•
Power strip•
Power up units
Plug all keypads into power strip. Each keypad's power supply 1.
should have a pigtail connected with a grounded three-prong plug,
and keypad should be assembled.
Plug the CMM1 Media Manager into the power strip. 2.
Wait for the keypads to boot up.3.
Naming the keypads
Each keypad should be named at this time. Give keypads unique 4.
names to avoid confusion when using the intercom or joining music
from another room. Write that name on a label and place it on the
aluminum frame of the keypad.
From the Initial Setup screen, choose Name, then use the wheel to 5.
scroll through the alphabet (upper and lower case), and press Select
to enter each letter. When nished, press Enter to save. Complete
the naming procedure for all keypads.
NAMING AND BINDING PROCEDURE
Binding the devices
The binding process associates the keypad with the media manager
(CMM1) by sharing a unique key and establishes communication and
identication of devices on the PLC network.
On the rst keypad, from the Initial Setup screen, scroll to and select 6.
Setup Gridcast Network.
Depress the binding button on the back of the CMM1. Wait for the 7.
LED to settle into a slow blinking mode (one second on/o) LED.
On the keypad, within 30 seconds scroll to and select Bind to Media 8.
Manager.
When the devices are bound to each other, the Status on the screen 9.
will change to Joined Network. Press Done to exit.
On the Initial Setup screen, press Done to complete the procedure.10.
Repeat the binding process for each additional keypad.11.
If there is an error or if the keypad shows "Waiting for others", power 12.
cycle the keypad and try again.
Once all keypads are bound to the Gridcast network, unplug all the
devices and proceed to location validation. Device names and binding
status are stored in memory and are not aected by power status.
- Media and Intercom System 1
- Installation Manual 1
- SAFETY INSTRUCTIONS 2
- Safety Instructions 2
- OUTDOOR ANTENNA CONNECTION 3
- Grounding an outdoor antenna 3
- TABLE OF CONTENTS 4
- T r ade Separator 6
- CMM1 FRONT AND BACK VIEW 7
- INSTALLATION MEDIA MANAGER 8
- Media Manager installation 8
- INSTALLATION PIGTAIL 9
- GRIDCAST VERIFICATION 12
- Deciphering the numbers 12
- Finding the reason 12
- INSTALLATION COMPONENTS 13
- MAKING THE CUTOUT 14
- Using the template 14
- Pull/Connect the wire 16
- Power pocket assembly 16
- INSTALLATION BACK BOX 16
- Install back box 16
- INSTALLATION AND CONNECTIONS 17
- Bring cables to keypad 17
- CAK1 keypad (back panel) 18
- Set time zone 19
- Required rmware update 19
- USING THE KEYPAD 20
- INTERCOM 21
- Intercom settings 21
- Using the intercom 21
- NETWORK MUSIC SETUP 22
- TECHNICAL SPECIFICATIONS 23
- Back Box Assembly 23
- CAK1 Keypad 23
- CMM1 Media Manager 23
- WARRANTY 24
Related products and manuals for Door intercom systems Russound Collage
(45 pages)Valueline VLMB34010O20 manuals
Owner’s manuals and user’s guides for HDMI cables Valueline VLMB34010O20.
We providing 1 pdf manuals Valueline VLMB34010O20 for download free by document types: Datasheet
Comments to this Manuals