Russound CA-LRC1 User Manual download pdf

INTRODUCTION

The (C)A-LRC1 from Russound

is the

complete solution for all of your remote

control requirements.It is designed to

operate source devices and the audio

system keypad.

The (C)A-LRC1 is also customizable to

allow for key configurations that meet

your specific needs. It’s also packed with

these features for you to choose from:

•Preprogrammed technology for

easy setup

•Designed for use with up to

seven devices

•Inclusive audio/video library

•Dedicated operation of audio system

keypad

This manual provides a basic overview

on how to set up and operate the (C)A-

LRC1. Please read the following instruc-

tions to see how easy setup is.

FEATURES AND FUNCTIONS

Use the Key Charts to learn how the

(C)A-LRC1 functions.

Key Charts

The LED (red light) blinks to

show that the remote control is

working and is sending signals.

Use SETUP for all programming

sequences.

Press PWR once to turn on or off

the selected home entertainment

component.

Press CBL, VCR,TV,1, 2,

3,or 4 once to select a

home entertainment-

component to control.

Use the keypad (0 ~ 9)

to directly select chan-

nels (for example,09

or 31).

Press MUTE once to turn sound

off or on.

Press ENTER once after entering

channel numbers on some TV

models.

Use VOL + (or VOL -) to raise (or

lower) the sound volume.

Use CH + (or CH -) to select the

next higher (or lower) channel.

Press LAST once to recall the last

channel and to page back one

screen in the main menu.

Press SLEEP to activate your TV’s

sleep timer. Or if none is avail-

able, press SLEEP to activate the

(C)A-LRC1’s sleep timer for

automatic shut-off of your TV.

Each key press (up to four) add

15 minutes to the sleep timer.

Press INPUT once to

switch the input of the

chosen component.

Use GUIDE to displaythe program

guide.

Use EXIT to exit out of the select-

ed component’s menu or guide.

Use the cursor keys to

move the cursor in the

program guide and

menu screens.

Use SELECT to choose options

from your selected component’s

menu or guide.

Use INFO to display current

channel and program informa-

tion.

Press MENU to access the menu

of your chosen component.

Use the transport keys

to control your VCR,or

CD or DVD player.

Use these keys to con-

trol CA-Series (use

CA-LRC1) or A-BUS

Multi-Source (use

A-LRC1) components.

INSTALLING BATTERIES

1. On the back of the (C)A-LRC1,push

the tab and lift off the battery cover.

2. Obtain two (2) fully-charged AA

alkaline batteries. Match the + and –

marks on the batteries to the + and

– marks in the battery case, then

insert the new batteries.

3. Press the battery cover back into

place. The tab should click when the

cover is locked.

4. Test the unit by pressing PWR and

any mode key (e.g., CBL,VCR,etc.).If

the batteries are inserted correctly,

the LED will blink once.

NOTE: When batteries need replacement,

the (C)A-LRC1 will blink twice with every

key press. Simply replace them and the

remote control will be restored to its full

functionality, including favorite settings.

PROGRAMMING

COMPONENT CONTROL

The (C)A-LRC1 can control up to eight

different components. Perform the fol-

lowing instructions for each component

you want controlled:

NOTE: For TV/VCR Combo control, see the

next section.

1. Turn on a component (e.g.,VCR)

and, if applicable, insert media,

(e.g., cassette or disc).

NOTE: Please read steps 2-4 completely

before proceeding. We recommend

highlighting or writing down the codes

and device you wish to program before

moving onto step 2.

2. On the (C)A-LRC1, press a compo-

nent key once (i.e.,CBL,VCR, TV,,

,,or ).Press and hold SETUP

until the LED blinks twice,then

release SETUP.

Components are assigned

to each component key.

=Cable, Satellite,DSS,Vid Acc.

=VCR,DVD,LDP,Audio Cassette,

DVR

=TV

=Satellite, DSS,Cable,Vid Acc.

=CD,Home Automation,MD,Amp,

Tun e r , Mi sc . A udio

=Amp,Tuner,Misc Audio, Home

Automation, MD

=Tuner,Amp,Misc,Audio, CD, Home

Automation, MD

3. Use the Manufacturer’s Codes (on the

back side) to locate the the type of

component and brand name and

then enter the first four-digit code

for your component. If performed

correctly, the LED will blink twice.

NOTE: If the LED did not blink twice, then

repeat steps 2 through 3 and try entering

the same code again.

4. Aim the (C)A-LRC1 at the component

and press PWR once. It should turn

off. If it does not respond, repeat steps

2-3, trying each code for your brand

until you find one that works.If it still

does not work, try searching for the

code (see Searching For Your Code).

NOTE: If the device does not have a PWR

key, press PLAY.

5. Repeat steps 1 through 4 for each

component you want the (C)A-LRC1

to control.

PROGRAMMING

TV/VCR COMBO CONTROL

Perform the following instructions to

control a TV/VCR Combo:

1. Turn on the TV/VCR Combo and

insert a video cassette.

NOTE: Please read steps 2-4 completely

before proceeding. We recommend

highlighting or writing down the code

for the brand you wish to program

before moving onto step 2.

2. On the (C)A-LRC1, press VCR.Press

and hold SETUP until the LED blinks

twice, then release SETUP.

3. Use the Setup Codes For TV/VCR

Combos (on the back side) to locate

the brand name and then enter the

first four-digit code for your compo-

nent.If performed correctly, the LED

will blink twice.

NOTE: If the LED did not blink twice, then

repeat steps 2 through 3 and try entering

the same code again.

4. Aim the (C)A-LRC1 at the component

and press PWR once. It should turn

off. If it does not respond, repeat steps

2-3, trying each code for your brand

until you find one that works.If it still

does not work, try searching for the

code (see Searching For Your Code).

NOTE: If the device does not have a PWR

key, press PLAY.

5. If you’ve located a setup code that

works, but it has a separate TV code,

you’ll also need to program it into the

(C)A-LRC1 to access volume control

as follows:

a. Press TV once.The LED will

blink twice.

b. Enter the TV code for your

TV/VCR Combo.If correct, the

LED will blink twice.

If there is no separate TV code listed,

you will need to perform the follow-

ing steps to access volume control:

a. Press and hold SETUP until the

LED blinks twice, then release

SETUP.

b. Enter 9 - 9 - 3 .The LED will

blink twice.

c. Press VCR once.The LED will

blink twice.

SEARCHING FOR YOUR CODE

If your device does not respond to the

(C)A-LRC1 after trying all codes listed

for your brand, or if your brand is not

listed at all, try searching for your code.

For example, to search for a code for

your TV:

1. On the (C)A-LRC1, press TV once.

2. Press and hold SETUP until the LED

blinks twice, then release SETUP.

3. Enter 9 - 9 - 1.The LED will

blink twice.

4. Aim the remote control at the the

TV and slowly alternate between

pressing PWR and TV.Stop when the

TV turns off.

NOTE: In the search mode, the (C)A-

LRC1 will send IR codes from its

library to the selected device, starting

with the most popular code first.

5. Press SETUP once to lock in the code.

6. To search for the codes of your other

components, repeat steps 1 through

5, but substitute the appropriate key

(i.e., CBL, VCR, TV,1,2, 3,or 4).

LEARNING CAPABILITY

To o p t i mize success,the learning process

should be conducted in an area where

there is a low level of IR emission. High

levels of “natural light”or energy effi-

cient fluorescent lights could interfere

with a learning event. The source and

target (learner) remotes should be no

more than 1 to 2 inches apart during a

learning event and the IR LEDs of the

two units should be aligned with each

other. The learning operation is initiated

as follows:

1. Press and hold SETUP until double

blink confirmation. Press 9 - 7 - 5 to

initiate learning mode.

2. Press [MODE] and key to be learned

(time out if no key pressed in 10 sec-

onds).

3. Visible LED flashes rapidly (time out

if no received signal detected in 4

sec.)

4. Hold teaching remote close to IR

LED and press key to be taught.

5. Visible LED goes out. Continue to

press teaching key until double blink

from visible LED. (One long blink

indicates a learning failure)

6. Repeat steps 2 through 5 as often as

desired (up to limit of memory).

7. Exit learning mode by pressing

SETUP,or by time out (10 seconds).

At step 5, one long blink indicates learning fail-

ure, which could be:

a. Bad capture (try again)

b. Memory full (delete some other

function)

c. Unlearnable code

Deleting a learned code:

To d el et e a le arned code, either overwrite

it with a new code on the same key, or

use the following sequence:

Press [MODE] then SETUP (press and

hold till you see two blinks) 9 - 7 - 6

then press the key you wish to delete

twice.

Sending a key’s original (preprogrammed)

function:

If a function is learned onto a key, then

SETUP - key will send the key’s original

function (as long as nothing else has

been learned or keymoved onto the

“shifted” key as well).

Interaction of learned keys and keymover:

•Ifboth a learned function and a key-

moved function are placed on the

same key, whichever was pro-

grammed last will take precedence.

•A learned function cannot be used as

a source for keymover. Keymover

always uses the key’s original func-

tion as the source.

Limitations on Learning

•There are certain device codes which

are not learnable. These include

multi-frequency codes (e.g.

Tel ef u n ken), some high frequency

codes, and other unusual formats.

•The learner will support IR codes

with carrier frequency up to 135

kHz.

•The unit can learn only one code per

key. It can’t be taught a sequence of

several keystrokes on one key.

•All keys with the exception of Modes,

and SETUP can be learned on.

•During a learning event the source

remote and target should be no more

than 1 to 2 inches apart.

•In some cases you may be required

to re-learn a code if it is not correctly

learned.

•The learning process should con-

ducted in an area where there is a

low levels of IR emission. High levels

of “nature light”or Energy efficient

fluorescent lights, could interfere

with a learning event.

•In general,it is not recommended to

learn a function to the Record Key.

The Record Key requires a double

key press to send the record function

in normal operation. The double key

press is lost when the Record key is

involved in most learning operations.

This lack of consistency in operation

generates a source of confusion for

the user and is best to be avoided

when possible. However, the Record

key is learnable.

•Typically,there are up to 24 buttons

that can be learned.

CHECKING THE CODES

If you have set up the (C)A-LRC1 using

the Searching For Your Code procedure,

you may need to find out which four-

digit code is operating your equipment:

For example, to find out which code is

operating your TV:

1. On the (C)A-LRC1, press TV once.

2. Press and hold SETUP until the LED

blinks twice, then release SETUP.

3. Enter 9 - 9 - 0.The LED will

blink twice.

4. To view the code for the first digit,

press 1 once. Wait 3 seconds, count

the LED blinks (e.g., 3 blinks = 3)

and write down the number.

NOTE: If a code digit is “0”, the LED

will not blink.

5. Repeat step 4 three more times for

remaining digits. Use 2 for the sec-

ond digit, 3 for the third digit, and 4

for the fourth digit.

6. To check for the codes of your other

components, repeat steps 1 through

5, but substitute the appropriate key

(i.e., CBL,VCR,TV,,,,or )

component you are checking.As

before, write down each four-digit

code.

RE-ASSIGNING DEVICE KEYS

The (C)A-LRC1 can be set up to control a

second TV or VCR, or any combination of

eight home entertainment components.

For example, to have the (C)A-LRC1

control a TV, a Cable Converter, and two

VCRs, you will need to re-assign the

key to operate the second VCR as fol-

lows:

1. On the (C)A-LRC1, press and hold

SETUP until the LED blinks twice,

then release SETUP.

2. Enter 9 - 9 - 2.The LED will

blink twice.

3. Press VCR once, then press once.

4. The key is now ready to be pro-

grammed for your second VCR. See

Programming Component Control.

To re-assign other device keys,repeat

steps 1 through 4 by substituting the key

sequence from the below chart for the

most popular components:

To Re-Assign Key:

Example: TV as 2nd VCR key:

SETUP - 9 - 9 - 2 - VCR - TV

When a re-assignment is done,the LED

will blink twice to confirm your choice.

At that time, you will need to program the

(C)A-LRC1 to control the new component

(see Programming Component Control).

To Change A Reassigned Key Back:

Example: TV back to TV:

SETUP - 9 - 9 - 2 - TV - TV

CHANGING VOLUME LOCK

The (C)A-LRC1 is set to control volume

of a component through your TV while

in the , , or mode. However, in

an Audio mode (i.e.,,,,or ),

you have separate control of your audio

component’s volume.

NOTE: This is not the keypad volume.

If your TV is not remote controllable, or

if you want volume to be controlled by a

different component, you can change the

Volu m e L o ck s et t i ng to control a volume

through a non-associated mode (e.g.,

through the cable in the TV mode).

To change Volume Lock to another

mode:

1. On the (C)A-LRC1, press and hold

SETUP until the LED blinks twice,

then release SETUP.

2. Enter 9 - 9 - 3 and then press any

mode key once (except TV).The LED

will blink twice.

3. Now, whenever you press VOL +,

VOL –,or MUTE,volume will be con-

trolled by your mode choice.

To change Volume Lock back to the

TV mode:

1. On the (C)A-LRC1, press and hold

SETUP until the LED blinks twice,

then release SETUP.

2. Enter 9 - 9 - 3 and then press TV.

The LED will blink twice.

3. Now, whenever you press VOL +,

VOL –,or MUTE on the (C)A-LRC1,

volume will be controlled by your TV.

TROUBLESHOOTING

PROBLEM: LED does not blink when you press a

key.

SOLUTION: Replace the batteries with two (2) new

AA alkaline batteries.

PROBLEM: LED blinks when you press a key, but

home entertainment component does not respond.

SOLUTION: Make sure the (C)A-LRC1 is aimed at

your home entertainment component and is not far-

ther than 15 feet away.

PROBLEM: (C)A-LRC1 does not control home enter-

tainment components or commands are not working

properly.

SOLUTION: Try a ll listed codes for the component

brands being set up.Make sure they can be operated

with an infrared remote control.

PROBLEM: TV/VCR combo does not respond prop-

erly.

SOLUTION: Use the VCR codes for your brand.

Some combo units may require both a TV code and

a VCR code for full operation.

PROBLEM: No volume on a 2nd TV.

SOLUTION: Follow instructions in Changing

Volu m e L oc k .

PROBLEM: CH+ , CH

,and LAST do not work for

your RCA TV.

SOLUTION:Due to RCA design (1983-1987), only

the original remote control will operate these func-

tions.

PROBLEM: Changing channels does not work

properly.

SOLUTION: If original remote control required

pressing ENTER to change channels,press ENTER on

the (C)A-LRC1 after entering the channel number.

PROBLEM: Trie d “Se a rch Method” a nd sti ll could

not find a working code.

SOLUTION: Try t he “S e arch Me thod”again after

clearing out the device key as follows: Press and hold

SETUP until red light blinks twice,then release. Next

enter 9 - 9 - 2.Then press and release the device key

to be cleared twice.

PROBLEM: Remote control does not turn on Sony

or Sharp TV/VCR Combo.

SOLUTION: For power on,these products require

programming TV codes. For Sony, use TV code

0000 and VCR code 0032.For Sharp, use TV code

0093 and VCR code 0048.

1 2

MANUFACTURER’S CODES 2

Summary of Contents

Page 1

INTRODUCTIONThe (C)A-LRC1 from Russound®is thecomplete solution for all of your remotecontrol requirements.It is designed tooperate source devices and

Page 2 - MANUFACTURER’S CODES

MANUFACTURER’S CODESSetup Codes for TVs: AOC0030, 0019,0185Admiral 0093, 0463Aiko 0092Akai 0030Alaron 0179Ambassador 0177America Action 0180Ampro 0751

Related models: A-LRC1

Comments to this Manuals

No comments

Russound CA-LRC1 User Manual

Browse online or download User Manual for Remote control Russound CA-LRC1. Russound CA-LRC1 User Manual [en] [ru] [de] [es] [fr] [it] [cs] [pl]

Summary of Contents

Related models: A-LRC1

Comments to this Manuals